All About Microsoft Windows And Technology !!!

Solved: Windows 10 Automatic Repair Loop “Your PC Did Not Start Correctly”

Getting windows Startup error Your PC did not start correctly? After a sudden power failure or upgrading your PC to a newer version. While turning on your computer, instead of booting to Desktop normally, Windows 10 displays an Automatic Repair screen with a message Your PC did not start correctly. As the screen mention itself that if you hit Restart button, the problem may solve automatically. But if this continues to happen after every reboot, you need to perform additional troubleshooting steps to solve this problem.

Before move to Troubleshooting steps first, understand why windows failed to start? Why windows perform the Automatic repair at startup and result Your PC Did Not Start Correctly? The problem mostly occurs if the Boot Configuration Data (BCD) file corrupted / Missing. There is chance Due to power failure or while system upgrade process the Master Boot Record (MBR) file get corrupted or missing. Some other Reasons are Any hardware changes such as re-installation of hard-drive, corrupted system files etc.

Fix Your PC Did Not Start Correctly Startup problem

If you are also suffering from this problem, windows unable to start normally. Windows Perform Automatic repair for hours and result your PC didn’t Start correctly. Here some applicable solutions to fix automatic repair your pc did not start correctly on Windows 10 and 8.1 computers.

Access Advanced options

As windows unable to start normally, we need to access advanced options. Where you can get various tools to fix windows Startup problems. Either you can click on Advanced options on the error screen, Or you can follow this steps to access windows Advanced options.

Windows Advanced Options

Perform Startup Repair

Here on Advanced options screen click on Startup repair option. When you select startup repair this will restart the window and start diagnostic process. And analyze the various settings, configuration options, and system files Especially look for :

  1. Missing/corrupt/incompatible drivers
  2. Missing/corrupt system files
  3. Missing/corrupt boot configuration settings
  4. Corrupt registry settings
  5. Corrupt disk metadata (master boot record, partition table, or boot sector)
  6. Problematic update installation

After complete, the repair process windows will Restart and start normally. If still having the same problem, showing your pc did not start correctly fallow next solution.

Run System File Checker Utility

If startup repair unable to fix the problem, Then try to run the SFC utility which scan and restore missing, corrupted system files. And fix the problem if any corrupted system file causing this startup problem your pc did not start correctly. To do this again access Advanced options And click on Command prompt. Here on advanced command prompt type command sfc /scannow and hit enter key to run system file checker.

The sfc utility check for missing corrupted system files and if found any the utility restore them from a special folder located on %WinDir%\System32\dllcache. Wait until 100% complete the scanning process After that restart windows check system start normally on next boot.

Run DISM command

If SFC scan results Windows Resource Protection found corrupt files but was unable to fix some of them then Run the DISM Tool which repairs the system image and enable SFC utility to do its job. To do this on same command prompt screen type dism.exe /online /cleanup-image /restorehealth and hit the enter key to run DISM Tool.

Rebuild Master Boot Record (MBR)

MBR or Master Boot Record is the data that is present in the first sector of any hard disk. It tells where the operating system is located so that it can be loaded. If Master Boot Record (MBR) file corrupted this may cause startup problem such as your pc did not start correctly.

After running DISM command Restart windows and check Windows start normally. If not then We need to repair the BCD Error by performing following command below. Again open command prompt form Advanced options and type command bellow one by one and hit the enter key to execute the same.

  • bootrec /fixmbr 
  • bootrec /fixboot
  • bootrec /ScanOS

fix bootrec Errors

Boot Configuration Data (BCD)

BCD or Boot Configuration Data is a firmware-independent database file which has boot-time configuration data. It is required by Windows Boot Manager and replaces the boot.ini that was used by NTLDR earlier. If this Boot Configuration Data (BCD) file get corrupted you may face different startup problem. If perform above solution didn’t solved the issue then try to rebuild the BCD file which may very helpful to Fix Your PC Did Not Start Correctly startup problem in Windows 10

To rebuild the BCD file, in the Command Prompt, type the following command and hit Enter:

bootrec /rebuildbcd

This will scan for other operating systems and lets you select the OS’s you want to add to BCD.Now there are two scenarios you can encounter:
(1)Total identified Windows installations: 0. Perform next commands below.
(2)Total identified Windows installations: 1. Type Y hit Enter and reboot your computer.
Type the commands below and hit Enter:
bcdedit /export c:bcdbackup
attrib c:bootbcd -h -r -s
ren c:bootbcd bcd.old
bootrec /rebuildbcd
Type Y and hit Enter.

That’s all you have successfully Rebuild the Boot Configuration Data file. Simply close the command prompt and Restart windows. check This time windows started normally without any startup errors.

Some Other Steps to Fix Your PC Did Not Start Correctly

If after performing startup repair, running SFC and DISM Tool, Rebuild MBR and BCD file Didn’t fix the startup problem. Then Try to boot into safe mode, Where windows start with minimum system requirements and allow to perform troubleshooting steps.

When you boot into safe mode first Turn off the Fast startup feature from Control Panel -> All Control Panel Items -> Power Options -> choose what the power buttons do -> change settings that are currently unavailable -> uncheck the Turn on Fast startup option.

Perform Windows 10/8.1 clean boot to diagnose and fix if any third party service/ startup application causes the issue.

If you notice the problem started after installing a third party application, simply uninstall the same from control panel -> program & Features -> right-click the recently installed application and uninstall.

Also, open Device Manager and check any driver with yellow triangle mark. If found any uninstall and re-install the driver. And update the drivers especially the Display driver To get rid most of the startup problems.

These Are some most applicable solutions to fix the windows automatic repair loop your PC did not start correctly startup error message in Windows 10/8/7. I hope to apply these solutions also fix the problem for you. Still, have any query or suggestions about this post, face any difficulty while applying the solutions feel free to discuss in comments below. Also, Read Fix Windows 10 Frequently Disconnect Internet Connection.

You might also like
Leave a comment

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More